Setting ~ Connection to Tester and Setting Test Spec ~<\/h3>\r\n\r\nPrepare Cable Harness Tester and PC installed the Software \"WireExpress\" <\/br>\r\nTurn on the tester and connect to the PC with PC cable.<\/br>\r\nStart the software.<\/br>\r\nNon-connection is displayed.<\/br>\r\nYou need to set the com port.<\/br><\/br>\r\n\r\nInput default Manager ID ,nacman790.<\/br>\r\nPlease open the Setting.<\/br>\r\n\r\nSet COM port. If the tester is connected to PC, the COM Port will be displayed.<\/br>\r\nIf it is not displayed, the tester is not connected properly. Please check the PC cable or the Software driver install. <\/br>\r\n\r\nAfter setting the COM, Please go back to MENU.<\/br>\r\nThe tester name will be displayed in a few seconds.<\/br>\r\nThen the connection is completed.<\/br><\/br>\r\n\r\nThere are two types of login. Checker, and Manager.<\/br>\r\nThe checker can operate only parts for testing.<\/br>\r\nThe Manager can operate all functions of this software including creating test data and management of test reports.<\/br>\r\nIf you log in, the buttons will be active depending on the login type.<\/br><\/br>\r\n\r\nLet's check the Setting again.<\/br>\r\nIn setting, you can set the default test specification, test setting and ID registration.<\/p><\/br>\r\n![\"How](\"https:\/\/www.naccorporation.com\/en\/wp-content\/uploads\/2020\/12\/How-to-set-the-test-spec-of-cable-testing-by-WireExpress.png\")
\r\n\r\n<\/div>\r\n\r\n
\r\n<\/hr>\r\n\r\nSampling ~ Creating Test Data ~<\/h3>\r\n\r\n
Create test data easily with OK cable.<\/br>\r\nPlease connect the test target via the jig.<\/br>\r\nInput the product name and comment.<\/br>\r\nThe comment is available for jigs and instructions.<\/br>\r\n\r\nIf you are ready, press the start button.<\/br>\r\nThe circuits are displayed. Please check them with the diagram.<\/br>\r\nPlease press register to complete creating test data.<\/p><\/br>\r\n![\"How](\"https:\/\/www.naccorporation.com\/en\/wp-content\/uploads\/2020\/12\/How-to-test-cable-harness-by-WireExpress.png\")
\r\n<\/div>\r\n
<\/hr>\r\n\r\nTest ~ Check Cables for OK or NG ~<\/h3>\r\n
This is the test screen.<\/br>\r\nIf you click start, the test will run.<\/br>\r\nTest results and measurements are displayed.<\/br>\r\nThe test was completed and passed.<\/br>\r\nThe test report is stored on the PC.<\/br><\/br>\r\n\r\nLet's check the test failed.<\/br>\r\n\r\nIt is in NG. <\/br>\r\nYou can check the NG content.<\/br><\/br>\r\n\r\nYou can change the start mode.<\/br>\r\nAuto-start is useful for consecutive tests.<\/br>\r\nIn this mode, the test starts by inserting connectors to the fixture after the first test passed.<\/p><\/br>\r\n![\"How](\"https:\/\/www.naccorporation.com\/en\/wp-content\/uploads\/2020\/12\/How-to-measure-resistance-of-cable-harness-by-WireExpress_03.png\")
\r\n<\/div>\r\n
\r\n<\/hr>\r\n\r\nMomentary Disconnection Testing for Cable Harness<\/h3>\r\n
If you conduct the Moment disconnection Testing,\r\nyou need to add the impacts by hitting or pulling.\r\n\r\nAs an example, let's test in the mode monitoring the disconnection until Enter is pressed.\r\nAfter applying the specified impact, press Enter.\r\n\r\nIf no disconnection occurs, OK is displayed.\r\nIf a disconnection is detected, NG is displayed.<\/p>\r\n<\/br>\r\n![\"How](\"https:\/\/www.naccorporation.com\/en\/wp-content\/uploads\/2020\/12\/How-to-test-moment-disconnection-of-cable-harness-by-WireExpress.png\")
\r\n<\/div>\r\n
\r\n<\/hr>\r\n\r\n\r\nData Management ~ Editing and Manual Creation of Test Data ~<\/h3>\r\n
Let's check the data management.<\/br>\r\nYou can create and edit the test data here.<\/br>\r\nEdit for detail setting such as setting resistance judgment value for each circuit, and so on.<\/br><\/br>\r\n\r\nPlease open the test data you created.<\/br>\r\nLet's edit this data.<\/br>\r\nIf you change the product name, this data will be saved as new test data.<\/br>\r\nYou can change the test spec here.<\/br>\r\nAdd the circuit by inputting information to the bottom cell column.<\/br>\r\n\r\nThe upper and lower resistance values can be set for each circuit.<\/br>\r\n\r\nFor creating data by manual, please click Manual Register.<\/br>\r\nYou can get blank data and input as you like.<\/p><\/br>\r\n![\"How](\"https:\/\/www.naccorporation.com\/en\/wp-content\/uploads\/2020\/12\/How-to-set-the-resistance-value-for-each-circuit-of-cable-harness-by-WireExpress.png\")
\r\n<\/div>\r\n
\r\n<\/hr>\r\n\r\nSearch ~ Check Adapters and Cables by Touching with Probe ~<\/h3>\r\n
Search is the function to check or test the connection by touching with the probe.<\/br>\r\nA simple search is for just checking the pin you touch with the probe.<\/br>\r\n\r\nThe memory test is for the test with search test data.<\/br>\r\nLet's create search test data.<\/br>\r\nPlease click register.<\/br>\r\n\r\nYou can select \"order search\" or \"random search\".<\/br>\r\n\r\nClick start and touch the pins.<\/br>\r\nCheck the pins. click register to save data.<\/br>\r\n\r\nLet's open the test data.<\/br>\r\nStart the test.<\/br>\r\nIf you touch all pins displayed, the test is passed.<\/br>\r\nTouch the wrong pin or can't find the connection, please click NG.<\/br>\r\n\r\nSame as test data, Search test data can be edited by manual.<\/p><\/br>\r\n![\"How](\"https:\/\/www.naccorporation.com\/en\/wp-content\/uploads\/2020\/12\/How-to-test-loose-wire-of-cable-harness-by-WireExpress.png\")
\r\n<\/div>\r\n
<\/hr>\r\n\r\nStep Test ~ Conduct More Than Two Tests Consecutively ~<\/h3>\r\n
\r\nStep test is a useful function for testing circuit-changing cables by the switch.<\/br>\r\nThis is the test to conduct more than two tests in a row.<\/br>\r\n\r\nLet's create STEP test data.<\/br>\r\nPlease select test data from the data you created.<\/br>\r\n \r\nOpen the step test data.<\/br>\r\nYou can run as a normal test.<\/br>\r\nThe second test is ready after the first test passed.<\/p><\/br>\r\n![\"How](\"https:\/\/www.naccorporation.com\/en\/wp-content\/uploads\/2020\/12\/How-to-test-switch-cable-harness-by-WireExpress.png\")
\r\n<\/div>\r\n
\r\n<\/hr>\r\n\r\nTest Report ~ Check Test Report ~<\/h3>\r\n
All test reports are saved by each test.<\/br>\r\nLet's check them in this part.<\/br>\r\nPlease decide the condition and click enter.<\/br>\r\n \r\nSelect the test report and click DETAIL.<\/br>\r\nSelect the line and click the test data. The test report will be written out.<\/br>\r\n \r\nOpen the test report.<\/br>\r\nIt contains information about the date and time, the test spec, the measured value, and the result.<\/p><\/br>\r\n![\"Test](\"https:\/\/www.naccorporation.com\/en\/wp-content\/uploads\/2020\/12\/Test-result-of-cable-harness-by-WireExpress.png\")
\r\n<\/div>\r\n
\r\n<\/hr>\r\n\r\nSelf-Diagnosis<\/h3>\r\n
\r\nSelf-diagnosis is the function to check the tester before testing.<\/br>\r\nFor the daily check, please conduct a scanner test.<\/br>\r\nRemove all test cables from the tester connectors before click start.<\/br>\r\n\r\nIt shows \"pass\".The tester is normal.<\/br>\r\nIf NG occurs, please check your environments.<\/br>\r\nPlease contact us in case of tester failure.<\/p><\/br>\r\n\r\n![\"How](\"https:\/\/www.naccorporation.com\/en\/wp-content\/uploads\/2020\/12\/How-to-check-cable-harness-tester-by-WireExpress.png\")
\r\n<\/div>\r\n
\r\n<\/hr>\r\n\r\n\r\n
Prepare Cable Harness Tester and PC installed the Software \"WireExpress\" <\/br>\r\nTurn on the tester and connect to the PC with PC cable.<\/br>\r\nStart the software.<\/br>\r\nNon-connection is displayed.<\/br>\r\nYou need to set the com port.<\/br><\/br>\r\n\r\nInput default Manager ID ,nacman790.<\/br>\r\nPlease open the Setting.<\/br>\r\n\r\nSet COM port. If the tester is connected to PC, the COM Port will be displayed.<\/br>\r\nIf it is not displayed, the tester is not connected properly. Please check the PC cable or the Software driver install. <\/br>\r\n\r\nAfter setting the COM, Please go back to MENU.<\/br>\r\nThe tester name will be displayed in a few seconds.<\/br>\r\nThen the connection is completed.<\/br><\/br>\r\n\r\nThere are two types of login. Checker, and Manager.<\/br>\r\nThe checker can operate only parts for testing.<\/br>\r\nThe Manager can operate all functions of this software including creating test data and management of test reports.<\/br>\r\nIf you log in, the buttons will be active depending on the login type.<\/br><\/br>\r\n\r\nLet's check the Setting again.<\/br>\r\nIn setting, you can set the default test specification, test setting and ID registration.<\/p><\/br>\r\n \r\n\r\n<\/div>\r\n\r\n
\r\n<\/hr>\r\n
Sampling ~ Creating Test Data ~<\/h3>\r\n\r\n
Create test data easily with OK cable.<\/br>\r\nPlease connect the test target via the jig.<\/br>\r\nInput the product name and comment.<\/br>\r\nThe comment is available for jigs and instructions.<\/br>\r\n\r\nIf you are ready, press the start button.<\/br>\r\nThe circuits are displayed. Please check them with the diagram.<\/br>\r\nPlease press register to complete creating test data.<\/p><\/br>\r\n\r\n<\/div>\r\n
<\/hr>\r\n
Test ~ Check Cables for OK or NG ~<\/h3>\r\n
This is the test screen.<\/br>\r\nIf you click start, the test will run.<\/br>\r\nTest results and measurements are displayed.<\/br>\r\nThe test was completed and passed.<\/br>\r\nThe test report is stored on the PC.<\/br><\/br>\r\n\r\nLet's check the test failed.<\/br>\r\n\r\nIt is in NG. <\/br>\r\nYou can check the NG content.<\/br><\/br>\r\n\r\nYou can change the start mode.<\/br>\r\nAuto-start is useful for consecutive tests.<\/br>\r\nIn this mode, the test starts by inserting connectors to the fixture after the first test passed.<\/p><\/br>\r\n\r\n<\/div>\r\n
\r\n<\/hr>\r\n
Momentary Disconnection Testing for Cable Harness<\/h3>\r\n
If you conduct the Moment disconnection Testing,\r\nyou need to add the impacts by hitting or pulling.\r\n\r\nAs an example, let's test in the mode monitoring the disconnection until Enter is pressed.\r\nAfter applying the specified impact, press Enter.\r\n\r\nIf no disconnection occurs, OK is displayed.\r\nIf a disconnection is detected, NG is displayed.<\/p>\r\n<\/br>\r\n\r\n<\/div>\r\n
\r\n<\/hr>\r\n\r\n
Data Management ~ Editing and Manual Creation of Test Data ~<\/h3>\r\n
Let's check the data management.<\/br>\r\nYou can create and edit the test data here.<\/br>\r\nEdit for detail setting such as setting resistance judgment value for each circuit, and so on.<\/br><\/br>\r\n\r\nPlease open the test data you created.<\/br>\r\nLet's edit this data.<\/br>\r\nIf you change the product name, this data will be saved as new test data.<\/br>\r\nYou can change the test spec here.<\/br>\r\nAdd the circuit by inputting information to the bottom cell column.<\/br>\r\n\r\nThe upper and lower resistance values can be set for each circuit.<\/br>\r\n\r\nFor creating data by manual, please click Manual Register.<\/br>\r\nYou can get blank data and input as you like.<\/p><\/br>\r\n\r\n<\/div>\r\n
\r\n<\/hr>\r\n
Search ~ Check Adapters and Cables by Touching with Probe ~<\/h3>\r\n
Search is the function to check or test the connection by touching with the probe.<\/br>\r\nA simple search is for just checking the pin you touch with the probe.<\/br>\r\n\r\nThe memory test is for the test with search test data.<\/br>\r\nLet's create search test data.<\/br>\r\nPlease click register.<\/br>\r\n\r\nYou can select \"order search\" or \"random search\".<\/br>\r\n\r\nClick start and touch the pins.<\/br>\r\nCheck the pins. click register to save data.<\/br>\r\n\r\nLet's open the test data.<\/br>\r\nStart the test.<\/br>\r\nIf you touch all pins displayed, the test is passed.<\/br>\r\nTouch the wrong pin or can't find the connection, please click NG.<\/br>\r\n\r\nSame as test data, Search test data can be edited by manual.<\/p><\/br>\r\n\r\n<\/div>\r\n
<\/hr>\r\n
Step Test ~ Conduct More Than Two Tests Consecutively ~<\/h3>\r\n
\r\nStep test is a useful function for testing circuit-changing cables by the switch.<\/br>\r\nThis is the test to conduct more than two tests in a row.<\/br>\r\n\r\nLet's create STEP test data.<\/br>\r\nPlease select test data from the data you created.<\/br>\r\n \r\nOpen the step test data.<\/br>\r\nYou can run as a normal test.<\/br>\r\nThe second test is ready after the first test passed.<\/p><\/br>\r\n\r\n<\/div>\r\n
\r\n<\/hr>\r\n
Test Report ~ Check Test Report ~<\/h3>\r\n
All test reports are saved by each test.<\/br>\r\nLet's check them in this part.<\/br>\r\nPlease decide the condition and click enter.<\/br>\r\n \r\nSelect the test report and click DETAIL.<\/br>\r\nSelect the line and click the test data. The test report will be written out.<\/br>\r\n \r\nOpen the test report.<\/br>\r\nIt contains information about the date and time, the test spec, the measured value, and the result.<\/p><\/br>\r\n\r\n<\/div>\r\n
\r\n<\/hr>\r\n
Self-Diagnosis<\/h3>\r\n
\r\nSelf-diagnosis is the function to check the tester before testing.<\/br>\r\nFor the daily check, please conduct a scanner test.<\/br>\r\nRemove all test cables from the tester connectors before click start.<\/br>\r\n\r\nIt shows \"pass\".The tester is normal.<\/br>\r\nIf NG occurs, please check your environments.<\/br>\r\nPlease contact us in case of tester failure.<\/p><\/br>\r\n\r\n\r\n<\/div>\r\n
\r\n<\/hr>\r\n\r\n\r\n